I'm not overly active here, mostly because I'm still really new to this and don't have a lot of value to add right now - hopefully someday I will become more knowledgeable, but for now I'm just learning as I go.
I just felt I needed to give a huge public thank you to Ben De lap! He has come through for me more than once now. I was stuck today and really in a bind for a file - I reached out to him with my situation and he was able to drop everything and get back to me within a couple of hours with it. ANYONE needing file conversions done, I highly recommend Ben!
big thank you to Ben!
-
- 4 Star Member
- Posts: 751
- Joined: Thu Jun 09, 2011 9:03 pm
Re: big thank you to Ben!
Ben is the man he always does good work.
-
- 3 Star Elite Contributing Member
- Posts: 411
- Joined: Thu Jun 25, 2015 4:06 pm
- Contact:
Re: big thank you to Ben!
I second the motion!!!!
PlasmaCam DHC2
Hyperthem PM65
Edwards 25T Ironworker
Miller Mig, Tig, Stick & Portable
Why pierce it when you can punch it!
Hyperthem PM65
Edwards 25T Ironworker
Miller Mig, Tig, Stick & Portable
Why pierce it when you can punch it!
- ben de lappe
- 4 Star Elite Contributing Member
- Posts: 1227
- Joined: Mon Aug 03, 2009 9:37 am
- Location: North Mississippi
Re: big thank you to Ben!
You are most welcome, I'm just glad that I was in a position where I could help.
ALL YOU GUYS are the ones deserving thanks. A few years ago I suffered a debilitating back injury. Couldn't keep my shop/table etc. For a long while I was lost, without any sense of purpose. Hell, fabrication was my whole life, over 25 years of it anyway. Over time I reconnected with Plasmaspider and began to draw again, using DXF's as a form of therapy I would help people with files or draw something just to share it, especially on those sleepless nights. Before long ALL YOU GUY'S began to recommend my work to any and all in need. Now, thanks to Plasmaspider and everyone that supports my work, I'm back to doing something that I truly love at my own pace.
For that I sincerely thank each and every one of you.
ALL YOU GUYS are the ones deserving thanks. A few years ago I suffered a debilitating back injury. Couldn't keep my shop/table etc. For a long while I was lost, without any sense of purpose. Hell, fabrication was my whole life, over 25 years of it anyway. Over time I reconnected with Plasmaspider and began to draw again, using DXF's as a form of therapy I would help people with files or draw something just to share it, especially on those sleepless nights. Before long ALL YOU GUY'S began to recommend my work to any and all in need. Now, thanks to Plasmaspider and everyone that supports my work, I'm back to doing something that I truly love at my own pace.
For that I sincerely thank each and every one of you.
- little blue choo
- 4 Star Member
- Posts: 1460
- Joined: Mon Mar 02, 2015 10:38 pm
- Location: Cherryville NC
- Contact:
Re: big thank you to Ben!
Just got a email from Ben this afternoon checking up on a job he helped me with last week. Now that's service, he actually check back in a couple of days to see if everything work out OK. All I can say is great service and very reasonable prices. Ben is becoming my new best friend. LOL Thanks again Ben.
Little Blue Choo / AKA Rick Walker
Little Blue Choo / AKA Rick Walker
Rick
Arclight 9600 4x8 table
Hypertherm PM65
Acc. Plate Marker, 4 inch Pipe Cutter, Wood Router package
Quincy Q54 compressor 2 stage, 5hp, 60 gal
Refrigerated air dryer & 4 stage filtration system
Software Mach 3, Sheetcam, Solid Edge 2D, Inkscape
Arclight 9600 4x8 table
Hypertherm PM65
Acc. Plate Marker, 4 inch Pipe Cutter, Wood Router package
Quincy Q54 compressor 2 stage, 5hp, 60 gal
Refrigerated air dryer & 4 stage filtration system
Software Mach 3, Sheetcam, Solid Edge 2D, Inkscape
-
- 1.5 Star Member
- Posts: 29
- Joined: Fri Aug 07, 2015 6:09 pm
Re: big thank you to Ben!
I personally know Ben, He is one Fine Man... his work is excellent and he is a Hell of a good friend...he has a passion for what we all get to do!!
- East German
- 4 Star Elite Contributing Member
- Posts: 580
- Joined: Sat Jan 05, 2013 8:21 am
- Location: Stapelburg Germany
Re: big thank you to Ben!
I would like to join ... Ben do very good work and all the best
Regards Peter
Regards Peter
Sorry for my language! The last English class was in 1982.
Homemade CNC Plasma-Watertable
MyPlasmCNC
Hypertherm Powermax 85
Machine Torch
Hypertherm Powermax 1100
Machine Torch
Homemade CNC Plasma-Watertable
MyPlasmCNC
Hypertherm Powermax 85
Machine Torch
Hypertherm Powermax 1100
Machine Torch