Been awhile since I shared hope this works-Coat Rack

Post by **superoverenginered** » Mon Nov 10, 2014 11:38 am

Nice lil coatrack I have been cutting just add diff name and go. People really love it! Enjoy

hulet.zip

Post by **gs123** » Mon Nov 10, 2014 2:16 pm

it looks good to me. thanks for sharing.

rtsplace · Post by **rtsplace** » Mon Nov 10, 2014 4:06 pm

superoverenginered, Nice file you diffinetly live up to your handle, lots of nice detail.
Thanks rtsplace/Ray

Post by **Zippo** » Mon Nov 10, 2014 6:43 pm

Thanks for posting.

ryansito · Post by **ryansito** » Mon Nov 10, 2014 9:26 pm

awesome thanks for sharing

Buzzard Gut · Post by **Buzzard Gut** » Tue Nov 11, 2014 9:33 pm

WOW! That's Bitchin. I can change the center to a deer head or ? and use it on a fire pit plate. Thanks!

mazika · Post by **mazika** » Sat Nov 15, 2014 8:07 am

CNCCAJUN · Post by **CNCCAJUN** » Sat Nov 15, 2014 1:42 pm

Looks great, very detailed . . .

Would make one change to improve it and perhaps make it more marketable.

Design the bottom edge where you currently have the coat hooks located to allow store bought "cast" coat hooks to be mounted. Basically design the bottom edge to compliment and accept the store bought hooks, holes and all.

You eliminate welding, add value, add to overall appearance, easier to ship and most important the store bought hooks are less likely to damage the coats.

You can get them @ Home Depot, Lowes, etc . . .

Just a thought . . .

Steve

Post by **superoverenginered** » Sun Nov 16, 2014 10:41 am

thanks for the thot and its a good thot except I live an hour and half away from any of those stores..special trip to go to the city. But all in all a good thot. I like the hand made look to be honest welding and all.

CNCCAJUN · Post by **CNCCAJUN** » Sun Nov 16, 2014 1:08 pm

superoverenginered wrote:thanks for the thot and its a good thot except I live an hour and half away from any of those stores..special trip to go to the city. But all in all a good thot. I like the hand made look to be honest welding and all.

I understand, I never think logistics. I have always lived in or very near a somewhat large city.

But now that you mention hand made, perhaps a small round disc (1/2" to 3/4") mounted horizontally on the end of the hook to support the coat.

Now that better than my first suggestion . . .

Steve

Post by **superoverenginered** » Mon Nov 17, 2014 9:20 am

Sure sounds great...I'll stick to my original design 25 strong on the design and not one person has said it harmed any fabric...I cut them out of .250 and round all edges off with belt sander so basically just like a hook you would buy from well anywhere...but yes I have made hooks like that before.

CNCCAJUN · Post by **CNCCAJUN** » Mon Nov 17, 2014 9:53 am

superoverenginered wrote:Sure sounds great...I'll stick to my original design 25 strong on the design and not one person has said it harmed any fabric...I cut them out of .250 and round all edges off with belt sander so basically just like a hook you would buy from well anywhere...but yes I have made hooks like that before.

Well see there is my "newbie" ignorance showing through . . .

I would have never thought of using 1/4" steel plate?

That has got to give a really massive look.

Please ignore my earlier suggestions.

I'm over here thinking 16 GA & 14 GA . . .sorry . . .

Steve

Post by **superoverenginered** » Mon Nov 17, 2014 10:13 am

its all good no worries...On all coatracks that I make that are not bent up curves I use .25 on hooks...Like I said no worries man!

CNCCAJUN · Post by **CNCCAJUN** » Mon Nov 17, 2014 11:18 am

I should have known that anybody with a name like SuperOverEngineered would not make anything out of 14Gauge . . .

Steve

Post by **superoverenginered** » Mon Nov 17, 2014 5:57 pm

haha thats funny yes I do normally over engineer stuff for sure...I do use 14ga alot to be honest but just in signs and stuff coatracks i make them out of 12 and 10ga mostly....Thank you for the laugh tho!!

Been awhile since I shared hope this works-Coat Rack

Been awhile since I shared hope this works-Coat Rack

Re: Been awhile since I shared hope this works

Re: Been awhile since I shared hope this works

Re: Been awhile since I shared hope this works

Re: Been awhile since I shared hope this works

Re: Been awhile since I shared hope this works-Coat Rack

Re: Been awhile since I shared hope this works-Coat Rack

Re: Been awhile since I shared hope this works-Coat Rack

Re: Been awhile since I shared hope this works-Coat Rack

Re: Been awhile since I shared hope this works-Coat Rack

Re: Been awhile since I shared hope this works-Coat Rack

Re: Been awhile since I shared hope this works-Coat Rack

Re: Been awhile since I shared hope this works-Coat Rack

Re: Been awhile since I shared hope this works-Coat Rack

Re: Been awhile since I shared hope this works-Coat Rack