Mach 4 THC moves 1.5" down to move instead of up

Mach3 and Mach4 questions, tips and topics can be posted here
Post Reply
ltwelding
1/2 Star Member
1/2 Star Member
Posts: 5
Joined: Wed Dec 07, 2022 6:44 pm

Mach 4 THC moves 1.5" down to move instead of up

Post by ltwelding »

Hello,
I am running a TruCut table with Hypertherm Plasma and Mach4. Everything works great but the THC function. Instead of moving up to travel to the cut it moves down from the torch height and hits my table.
adbuch
6 Star Elite Contributing Member
6 Star Elite Contributing Member
Posts: 8598
Joined: Thu Sep 21, 2017 5:22 pm
Location: Tucson, Arizona
Contact:

Re: THC moves 1.5" down to move instead of up

Post by adbuch »

Sounds like you've got a sign reversed somewhere - plus instead of minus, or visa versa.
David
ltwelding
1/2 Star Member
1/2 Star Member
Posts: 5
Joined: Wed Dec 07, 2022 6:44 pm

Re: THC moves 1.5" down to move instead of up

Post by ltwelding »

how do I change that? tried changing plus and minus ports around in configure but it did not work
adbuch
6 Star Elite Contributing Member
6 Star Elite Contributing Member
Posts: 8598
Joined: Thu Sep 21, 2017 5:22 pm
Location: Tucson, Arizona
Contact:

Re: THC moves 1.5" down to move instead of up

Post by adbuch »

I don't use Mach4, but I do use Mach3 on one of my cnc routers. I have never had your problem, so I couldn't tell you right of the top of my head. Is this a new table to you or one that was working and just started having this problem? Does this table work fine with thc turned off?
David
ltwelding
1/2 Star Member
1/2 Star Member
Posts: 5
Joined: Wed Dec 07, 2022 6:44 pm

Re: THC moves 1.5" down to move instead of up

Post by ltwelding »

Yes it does work with the THC off, but my thinner metal heats up and changes heights and ends up messing my cut up. This table ran mach3 flawlessly with thc but the computer that came with it crashed shortly after I bought it. I thought uprgrading to Mach4 would be a good idea, it has been one headache after another.
adbuch
6 Star Elite Contributing Member
6 Star Elite Contributing Member
Posts: 8598
Joined: Thu Sep 21, 2017 5:22 pm
Location: Tucson, Arizona
Contact:

Re: THC moves 1.5" down to move instead of up

Post by adbuch »

Maybe try going back to Mach3.
David
ltwelding
1/2 Star Member
1/2 Star Member
Posts: 5
Joined: Wed Dec 07, 2022 6:44 pm

Re: THC moves 1.5" down to move instead of up

Post by ltwelding »

The computer that had everything on it crashed
adbuch
6 Star Elite Contributing Member
6 Star Elite Contributing Member
Posts: 8598
Joined: Thu Sep 21, 2017 5:22 pm
Location: Tucson, Arizona
Contact:

Re: THC moves 1.5" down to move instead of up

Post by adbuch »

You can download the free trial version of Mach3 below.

https://www.machsupport.com/software/mach3/

If you install it and it works for you, then you could purchase the license.
Or perhaps one of the other members will know more about your thc and help you diagnose your problem.

David
User avatar
acourtjester
6 Star Elite Contributing Member
6 Star Elite Contributing Member
Posts: 7770
Joined: Sat Jun 02, 2012 6:04 pm
Location: Pensacola, Fla

Re: THC moves 1.5" down to move instead of up

Post by acourtjester »

You did not state what brand the THC unit is. You should look at the input to the BOB for the THC output signals, Make sure the up signal goes to the up pin on the BOB in Mach 4 of 3 which ever you are using. Many of the THCs have a up and down LED and Mach on the diagnostic page should also show up and down indicators, check to see that they are lighting the same directions if you have a test mode on the THC. I hope you did not switch the plus and minus inputs from the plasma unit to the THC.
DIY 4X4 Plasma/Router Table
Hypertherm PM65 Machine Torch
Drag Knife and Scribe
Miller Mig welder
13" metal lathe
Small Mill
Everlast PowerTig 255 EXT
ltwelding
1/2 Star Member
1/2 Star Member
Posts: 5
Joined: Wed Dec 07, 2022 6:44 pm

Re: THC moves 1.5" down to move instead of up

Post by ltwelding »

I am using a PMDX-411. is that in the input signals to check plus and minus?
User avatar
acourtjester
6 Star Elite Contributing Member
6 Star Elite Contributing Member
Posts: 7770
Joined: Sat Jun 02, 2012 6:04 pm
Location: Pensacola, Fla

Re: THC moves 1.5" down to move instead of up

Post by acourtjester »

I cannot answer that, you may want to post your question on their Tech Support site.
https://www.pmdx.com/PMDX-Forums/index. ... &board=9.0
DIY 4X4 Plasma/Router Table
Hypertherm PM65 Machine Torch
Drag Knife and Scribe
Miller Mig welder
13" metal lathe
Small Mill
Everlast PowerTig 255 EXT
weldguy
4 Star Elite Contributing Member
4 Star Elite Contributing Member
Posts: 1928
Joined: Fri Apr 17, 2009 11:48 am

Re: THC moves 1.5" down to move instead of up

Post by weldguy »

Did you do your post processing on the same computer that crashed? If so you would have had to re-install that and it may not be configured properly for use with your THC.
Post Reply

Return to “Mach3 & Mach4 CNC”