DIY Oven Build - Amperage Questions

Learn and share powder coating techniques, experiences, and product knowledge here.
Post Reply
Beej54
1/2 Star Member
1/2 Star Member
Posts: 1
Joined: Fri Nov 17, 2023 6:29 pm

DIY Oven Build - Amperage Questions

Post by Beej54 »

Hello All!

I have been powder coating for a few years and finally going to build a slightly bigger oven than a regular home unit now I have moved into a place with a bigger garage.

Now my question is (and I had a search but couldn't find an exact answer to this), I had a 50 Amp service at my old place, but this new one was only wired in the garage for 30 Amp. After receiving an estimate for the replacement, it got me thinking about how I can make the 30A work... when I realized the technical specs for the oven I bought to harvest parts list the Circuit Breaker as 30A! The unit is a Bosch Wall Oven (HBL5451UC) so no hot plates etc, 6,325 W / 240 V.

Would I be correct in assuming this will in fact work on the installed 30A service correctly? I can wire things just fine as the "mechanical aspect" of these tasks is very straightforward for me, but understanding the math behind the draw and safety limits/ headroom on electrical systems is a bit foreign to me.

Any help or clarification on this would greatly appreciated!
User avatar
rdj357
4 Star Elite Contributing Member
4 Star Elite Contributing Member
Posts: 1184
Joined: Sun Mar 11, 2012 4:40 pm
Location: Tahlequah, OK
Contact:

Re: DIY Oven Build - Amperage Questions

Post by rdj357 »

Hmm - a circuit breaker is typically made to carry 80% of its load rating continuously. For a 30 amp breaker that would be 24 amps. It will be close and will possibly work depending on what your actual supply voltage at the new place. If it is a full 240v then it would draw 26.4 amps so depending on how long the elements stayed on continuously, would likely cause the breaker to get too hot and trip. If it’s closer to 220v and the wattage rating you posted is the 240v rating then the draw on 220v would be about 24.2 and would likely be just fine.

Check your voltage at the new place and divide it by the resistance of the elements to get the amperage. Based on what you said, I would expect resistance to be about 9.09 ohms but can’t hurt to double check. Know that the lower the voltage, the lower the actual wattage you’ll get in the oven - at that 220v guess, you’d be getting 5324 watts.
Robert Johnson
PlasmaCAM GURU & Instructor
FourNinety Creations & Learn PC, LLC
(918) 457-0289 * Robert@490Creations.com
Did I help and you want to help me out? Buy me a coffee! - Thanks!
I am not affiliated with PlasmaCAM, Inc. in any way. I offer training on their equipment and software. All product and company names are trademarks™ or registered® trademarks of their respective holders. Use of them are for nominative purposes only and does not imply any affiliation with or endorsement by them.
User avatar
acourtjester
6 Star Elite Contributing Member
6 Star Elite Contributing Member
Posts: 7870
Joined: Sat Jun 02, 2012 6:04 pm
Location: Pensacola, Fla

Re: DIY Oven Build - Amperage Questions

Post by acourtjester »

If you stay with the parts you scrounged from the Bosch unit you should be fine. It sounds like a single element or only bake or broil but not both at the same time. That would limit the current draw on the breaker, it will pull full power until set temps are reached then a coasting draw to maintain set temps. The DIY oven I built has 2 large and 2 small top burner elements, after suing I dropped back to only 2 large and it gets to 400 degree fine.
powder coat oven (4).jpg
oven inside A.jpg

You currently do not have access to download this file.
To gain download access for DXF, SVG & other files Click Here

DIY 4X4 Plasma/Router Table
Hypertherm PM65 Machine Torch
Drag Knife and Scribe
Miller Mig welder
13" metal lathe
Small Mill
Everlast PowerTig 255 EXT
statspp
1/2 Star Member
1/2 Star Member
Posts: 1
Joined: Mon Jun 03, 2024 7:44 am

Re: DIY Oven Build - Amperage Questions

Post by statspp »

Has anyone heard of ovens from the Polish company ROMER? Apparently, they are good and reliable, and they offer various types of ovens
https://romerpp.pl/lang-en/33-how_to_bu ... rnace.html
Post Reply

Return to “Powder Coat”