Where do you get your compressed air Flex hoses?
-
- 1/2 Star Member
- Posts: 9
- Joined: Tue Jan 24, 2023 6:31 pm
Where do you get your compressed air Flex hoses?
Afternoon,
I just picked up a my air compressor and designing the layout for the copper piping. There are 3 sections where the copper will need a flex hose. From the compressor to the pipe, when the pipe passes through the shed wall into the garage, and where I have to sneak it behind some cabinets - one 12" and 2 18".
I read online that you should get Stainless Steel braided air lines... but Amazon has one seller and they are way expensive. $50-75 per line? and I don't see SS 'air lines' at HD/Lowes.
Is a SS compressed air line, the same as the equivalent gas line that you would find at your local home store?
Or should I just use regular air hose? idk, looking for insight.
Thanks,
J
I just picked up a my air compressor and designing the layout for the copper piping. There are 3 sections where the copper will need a flex hose. From the compressor to the pipe, when the pipe passes through the shed wall into the garage, and where I have to sneak it behind some cabinets - one 12" and 2 18".
I read online that you should get Stainless Steel braided air lines... but Amazon has one seller and they are way expensive. $50-75 per line? and I don't see SS 'air lines' at HD/Lowes.
Is a SS compressed air line, the same as the equivalent gas line that you would find at your local home store?
Or should I just use regular air hose? idk, looking for insight.
Thanks,
J
- djreiswig
- 4.5 Star Elite Contributing Member
- Posts: 2027
- Joined: Thu Nov 19, 2015 10:02 pm
- Location: SE Nebraska
Re: Where do you get your compressed air Flex hoses?
I have used premade hydraulic hoses in the past. They are way over rated for the pressure you will be running, so no worry of splitting. They're also readily available in different lengths and fittings. If you want to be able to split your plumbing later, use JiC swivel fittings. Or you can use NPT and install a union fitting.
2014 Bulltear (StarLab) 4x8
C&CNC EtherCut
Mach3, SheetCam, Draftsight
Hypertherm PM65
Oxy/Acetylene Flame Torch
Pneumatic Plate Marker, Ohmic, 10 inch Rotary Chuck (in progress)
C&CNC EtherCut
Mach3, SheetCam, Draftsight
Hypertherm PM65
Oxy/Acetylene Flame Torch
Pneumatic Plate Marker, Ohmic, 10 inch Rotary Chuck (in progress)
-
- 6 Star Elite Contributing Member
- Posts: 10234
- Joined: Thu Sep 21, 2017 5:22 pm
- Location: Tucson, Arizona
- Contact:
Re: Where do you get your compressed air Flex hoses?
I would not recommend gas flex lines like the ones used on hot water heaters and other appliances for your application. In general these are rated for a maximum pressure of 80 psi, which is much lower than the approx. 150 - 175 psi you may have coming from your compressor. I have my air compressor air outlet connected to the rigid copper piping by a 3/4" stainless steel flex hose with a union fitting. See photos below.
I run 3/4" rigid copper throughout the shop. It reduces down to 1/2" ID pipe in the machine shop and to the refrigerated dryer, then 3/8" rubber hose from the dryer to the plasma cutter. Perhaps tell us your plan: how long is your air piping/hose run from the compressor to your plasma cutter, etc.
David
You currently do not have access to download this file.
To gain download access for DXF, SVG & other files Click Here
-
- 1/2 Star Member
- Posts: 9
- Joined: Tue Jan 24, 2023 6:31 pm
Re: Where do you get your compressed air Flex hoses?
My total run is about 40’… but I decided to do some snaking up and down w valves to drain… so that would make it 75’. Im just trying to make sure air is condensed. Is that too long/short?
So hydraulic hoses huh? Recommendation on where to get? Amazon i assume. Ill check it out.
J
So hydraulic hoses huh? Recommendation on where to get? Amazon i assume. Ill check it out.
J
-
- 1/2 Star Member
- Posts: 9
- Joined: Tue Jan 24, 2023 6:31 pm
Re: Where do you get your compressed air Flex hoses?
Also… where should i look for not too expensive regulators?
Thanks
J
Thanks
J
- djreiswig
- 4.5 Star Elite Contributing Member
- Posts: 2027
- Joined: Thu Nov 19, 2015 10:02 pm
- Location: SE Nebraska
Re: Where do you get your compressed air Flex hoses?
I get them from here, but they're local to me. I'm sure you can find one on Amazon.
https://www.surpluscenter.com/Hydraulic ... ssemblies/
https://www.surpluscenter.com/Hydraulic ... ssemblies/
2014 Bulltear (StarLab) 4x8
C&CNC EtherCut
Mach3, SheetCam, Draftsight
Hypertherm PM65
Oxy/Acetylene Flame Torch
Pneumatic Plate Marker, Ohmic, 10 inch Rotary Chuck (in progress)
C&CNC EtherCut
Mach3, SheetCam, Draftsight
Hypertherm PM65
Oxy/Acetylene Flame Torch
Pneumatic Plate Marker, Ohmic, 10 inch Rotary Chuck (in progress)
- djreiswig
- 4.5 Star Elite Contributing Member
- Posts: 2027
- Joined: Thu Nov 19, 2015 10:02 pm
- Location: SE Nebraska
Re: Where do you get your compressed air Flex hoses?
I got my regulators from harbor freight.
2014 Bulltear (StarLab) 4x8
C&CNC EtherCut
Mach3, SheetCam, Draftsight
Hypertherm PM65
Oxy/Acetylene Flame Torch
Pneumatic Plate Marker, Ohmic, 10 inch Rotary Chuck (in progress)
C&CNC EtherCut
Mach3, SheetCam, Draftsight
Hypertherm PM65
Oxy/Acetylene Flame Torch
Pneumatic Plate Marker, Ohmic, 10 inch Rotary Chuck (in progress)
-
- 1/2 Star Member
- Posts: 9
- Joined: Tue Jan 24, 2023 6:31 pm
Re: Where do you get your compressed air Flex hoses?
Hf ones are not junk? Any in particular?
J
J
- SegoMan DeSigns
- 4 Star Member
- Posts: 992
- Joined: Sat Jan 06, 2018 4:45 pm
- djreiswig
- 4.5 Star Elite Contributing Member
- Posts: 2027
- Joined: Thu Nov 19, 2015 10:02 pm
- Location: SE Nebraska
Re: Where do you get your compressed air Flex hoses?
Haven't bought any recently, but I don't recall them having a very big selection. I just got whatever was cheap in the correct size.
2014 Bulltear (StarLab) 4x8
C&CNC EtherCut
Mach3, SheetCam, Draftsight
Hypertherm PM65
Oxy/Acetylene Flame Torch
Pneumatic Plate Marker, Ohmic, 10 inch Rotary Chuck (in progress)
C&CNC EtherCut
Mach3, SheetCam, Draftsight
Hypertherm PM65
Oxy/Acetylene Flame Torch
Pneumatic Plate Marker, Ohmic, 10 inch Rotary Chuck (in progress)
-
- 5 Star Elite Contributing Member
- Posts: 2759
- Joined: Thu Jul 24, 2008 11:15 am
Re: Where do you get your compressed air Flex hoses?
I have always used standard air hose for connections like what you are describing. Super cheap and has never let me down. Metal hose is required from the pump to the tank due to the heat but after that I have never needed anything fancy.
-
- 1/2 Star Member
- Posts: 9
- Joined: Tue Jan 24, 2023 6:31 pm
Re: Where do you get your compressed air Flex hoses?
Another question here. What do you recommend I use for the flex hose, air coupler sizes, to reduce air restriction?
I am using 3/4" copper which branches to 1/2" - if that helps with an answer.
I've seen folk buy special air couplers which are supposed to have larger ID than others... Should I use 3/8", 1/2" or what do you recommend?
Thanks ,
J
I am using 3/4" copper which branches to 1/2" - if that helps with an answer.
I've seen folk buy special air couplers which are supposed to have larger ID than others... Should I use 3/8", 1/2" or what do you recommend?
Thanks ,
J
-
- 6 Star Elite Contributing Member
- Posts: 10234
- Joined: Thu Sep 21, 2017 5:22 pm
- Location: Tucson, Arizona
- Contact:
Re: Where do you get your compressed air Flex hoses?
I use standard air couplers purchased from Grainger. Harbor Freight sells the same thing of similar quality. I wouldn't worry about "air restriction".
Yes - I also use 3/4" copper around the main shop and spray booth, which branches down to 1/2" for the machine shop and garage.
David
Yes - I also use 3/4" copper around the main shop and spray booth, which branches down to 1/2" for the machine shop and garage.
David
You currently do not have access to download this file.
To gain download access for DXF, SVG & other files Click Here
- djreiswig
- 4.5 Star Elite Contributing Member
- Posts: 2027
- Joined: Thu Nov 19, 2015 10:02 pm
- Location: SE Nebraska
Re: Where do you get your compressed air Flex hoses?
I don't care for the cheap couplers. I use Milton ones.
2014 Bulltear (StarLab) 4x8
C&CNC EtherCut
Mach3, SheetCam, Draftsight
Hypertherm PM65
Oxy/Acetylene Flame Torch
Pneumatic Plate Marker, Ohmic, 10 inch Rotary Chuck (in progress)
C&CNC EtherCut
Mach3, SheetCam, Draftsight
Hypertherm PM65
Oxy/Acetylene Flame Torch
Pneumatic Plate Marker, Ohmic, 10 inch Rotary Chuck (in progress)
-
- 6 Star Elite Contributing Member
- Posts: 10234
- Joined: Thu Sep 21, 2017 5:22 pm
- Location: Tucson, Arizona
- Contact:
Re: Where do you get your compressed air Flex hoses?
I use both the high dollar Granger Speedaire and the HF version. Both perform well for me. I also use many of the Grizzly tools even though some thumb their noses at them. Some are made in Taiwan (the better ones) and others made in China. In some cases it is ok to get more "bang for the buck". These days - most of this stuff is manufactured "off shore" - regardless of branding.
David
-
- 4 Star Elite Contributing Member
- Posts: 807
- Joined: Mon Dec 26, 2011 8:37 pm
- Location: Southeast Missouri
Re: Where do you get your compressed air Flex hoses?
I used to use nothing but Milton quick couplers and then started getting cheap so I started buying HF couplers and in recent years the HF couplers leak from day one so I'm back to buying Milton.
Allen
Allen
- Joe Jones
- 5 Star Elite Contributing Member
- Posts: 3492
- Joined: Sat Oct 11, 2014 2:33 pm
- Location: Franklin, KY., USA
- Contact:
Re: Where do you get your compressed air Flex hoses?
An air coupling that leaks is one of my pet peeves.
Joe
Joe
PlasmaCam 4x4, Samson 510 table, Go Torch, + more
AD-AH-AM-AN-3D-CS-MU-PC - Upgrades
X-TOOL D1 PRO (x 4) F1, S1 (x3), P2 (x2), F1 ULTRA (x2) with conveyors, M1 ULTRA (x2) + accs.
LaserPecker 1 PRO, LP-2, LP-4 + accs
50 Watt GALVO fiber
TYVOK Spider S1 60W Diode Laser 49" x 96"
SwiftShape 3-in-1 machine
CreatBot D600 PRO
Stratasys Fortus 400mc
BIGREP Studio Gen 2
MODIX Big Meter
MakerBOT Z-18 3D Printer
Bernardo Mach 55 TON Ironworker
FREE DesignEdge Training Online Via ZOOM!
AD-AH-AM-AN-3D-CS-MU-PC - Upgrades
X-TOOL D1 PRO (x 4) F1, S1 (x3), P2 (x2), F1 ULTRA (x2) with conveyors, M1 ULTRA (x2) + accs.
LaserPecker 1 PRO, LP-2, LP-4 + accs
50 Watt GALVO fiber
TYVOK Spider S1 60W Diode Laser 49" x 96"
SwiftShape 3-in-1 machine
CreatBot D600 PRO
Stratasys Fortus 400mc
BIGREP Studio Gen 2
MODIX Big Meter
MakerBOT Z-18 3D Printer
Bernardo Mach 55 TON Ironworker
FREE DesignEdge Training Online Via ZOOM!