A120 problem
-
- 3.5 Star Elite Contributing Member
- Posts: 573
- Joined: Fri Jul 20, 2012 12:08 pm
A120 problem
Hi.I bought a used table with A 120 TD plasma.Had to change from 3 phase to single phase.went by the book with the jumper bars and changed the switch to low voltage.Can't get it to cut now has a flashing red code and a flashing green 65 code.Checked input voltage and it's at 230V.Don't know whats wrong.
5x10 table,Precision plasma gantry,Cand CNC electronics,Hypertherm 65 plasma,King lathe and mill,255 lincoln mig welder.Dawson Creek BC. Much modified Fastcut 4x8 plasma table with Ethercut
-
- 3.5 Star Member
- Posts: 511
- Joined: Wed Apr 23, 2014 2:48 pm
Re: A120 problem
Did you also tape back/disconnect the red input wire? My A120 was configured for single phase from the factory.. (Three wire cord too). The 82(A-60 now) I just picked up new in box was a 460 volt three phase configured machine from the factory. Just the switch to low voltage, and the buse bar jumper installed to the L2-L3 contacts on the side of the contactor that has the Jumper wire going to L1-L4. That is all there is to hook up for single phase.
-
- 3.5 Star Elite Contributing Member
- Posts: 573
- Joined: Fri Jul 20, 2012 12:08 pm
Re: A120 problem
Mine has 2 copper buss bars to install so each bar gets a 120 line is that right?
5x10 table,Precision plasma gantry,Cand CNC electronics,Hypertherm 65 plasma,King lathe and mill,255 lincoln mig welder.Dawson Creek BC. Much modified Fastcut 4x8 plasma table with Ethercut
-
- 3.5 Star Member
- Posts: 511
- Joined: Wed Apr 23, 2014 2:48 pm
Re: A120 problem
It been a while since I had the A-120 victor, but that one came setup for Single phase, from the cord on forward.. Only a 3 wire cord, so I did not have to mess with any Jumpers on that one. You are probably correct in that it uses a different buse setup over the A-60..
Looks like it...but the link does not work here.. Service manual shows it very clear. Might have to call victor on this one..
http://victortechnologies.com/IM_Upload ... ec2013.pdf
Looks like it...but the link does not work here.. Service manual shows it very clear. Might have to call victor on this one..
http://victortechnologies.com/IM_Upload ... ec2013.pdf
-
- 3.5 Star Elite Contributing Member
- Posts: 573
- Joined: Fri Jul 20, 2012 12:08 pm
Re: A120 problem
Thanks Brandx.
5x10 table,Precision plasma gantry,Cand CNC electronics,Hypertherm 65 plasma,King lathe and mill,255 lincoln mig welder.Dawson Creek BC. Much modified Fastcut 4x8 plasma table with Ethercut
-
- 2 Star Member
- Posts: 52
- Joined: Mon Jun 06, 2016 2:58 pm
Re: A120 problem
are You guys happy with your Thermal dynamics cutter? This is the first one I have ever owned. used it for about 8 months. Yesterday it quite working. Called Victor and they had me run through several test. Bottom line I have to send it to service center to be repaired. Do any of you own a second machine just encase it goes down on you?
TruCut 5x10
Victor Plasma
Thermal Dynamics
Sheet Cam
Rhino3d
Bobcad
Victor Plasma
Thermal Dynamics
Sheet Cam
Rhino3d
Bobcad
-
- 2 Star Member
- Posts: 52
- Joined: Mon Jun 06, 2016 2:58 pm
Re: A120 problem
is it common to have problems with the Thermal dynamics victor a120?
TruCut 5x10
Victor Plasma
Thermal Dynamics
Sheet Cam
Rhino3d
Bobcad
Victor Plasma
Thermal Dynamics
Sheet Cam
Rhino3d
Bobcad
-
- 1/2 Star Member
- Posts: 1
- Joined: Wed Dec 19, 2018 1:44 am
Re: A120 problem
Thank you pilpedia official Brandx