4x4 welding table help

[richiemirtsching]

Looking for a 4x4 welding table DXF or Plasma Cam Pattern.Any help would be greatly appreciated. Thank you.

[SONIC]

What exactly do you need?
My welding table is a 4x8 piece of 3/8 with legs.

[sphurley]

Guy on ebay, took the tab and slot tables design (and photos) and sells the plans

[hemichargersrt8]

here is one version I have drawn. I laser cut and carefully welded to reduce excessive heat. Because of the puzzle tabs, the table assembled very flat and stable. I will upload the accessories when I get a chance.

fixture top 29-5X47-5 375 ms 1 pce.dxf

fixture rib short 29-5X47-5 187 ms 5 pcs.dxf

fixture rib long 29-5X47-5 187 ms 4 pcs.dxf

[radicalrescue]

hemichargersrt8 thanks for that file i have wanted a table like that for years

[motoguy]

hemichargersrt8 - thank you for sharing! I have wanted to design a table like this for a while now. Thanks again!

[Largemouthlou]

Thank you very much!!

[hemichargersrt8]

Here is the large accessory piece. As with the table, all the parts are cut with 3/16" mild steel. I allowed .003" clearance around all puzzle tables. 5/8" holes for standard table clamps.

fixture square side plate 187 ms 2 pcs.dxf

fixture square top plate 187 ms 2 pcs.dxf

fixture square front plate 187 ms 1 pce.dxf

fixture square middle plate 187 ms 1 pce.dxf

fixture square bottom plate 187 ms 1 pce.dxf

[hemichargersrt8]

here is a pic of the underside of the table

[little blue choo]

Darn you hemichargersrt8 now I have to upgrade my welding table. Love it man love it! By the way I'm a MOPAR man also, most of mine are 1973 and back. Dusters, Darts, Cuda and Roadrunner.

Rick

[hemichargersrt8]

Rick, I will keep adding accessories for this table. I am a long time mopar fan, but really since 2006, been a SRT buyer. Current ride is a plum crazy 2016 hellcat challenger. Quite the ride!

[hemichargersrt8]

small angle fixture

fixture angle gusset 187 ms 4 pcs.DXF

fixture angle long 187 ms 2 pcs.DXF

[Gamelord]

Wow, thank you for the share! Awesome design.

[richiemirtsching]

that is what I'm looking for you are awesome

[hemichargersrt8]

Here is a shelf and light mount for the table. I cut slots in the shelf panel to make bending by hand easier. Bend the front and back flanges first and then fold the end panels up. Tack weld as necessary. The shelf is 11 ga mild steel and the post mounting pads are 3/16" mild steel with 1 x 1 posts

fixture table with shelf light mount.JPG

fixture shelf.JPG

fixture shelf flat.JPG

fixture shelf assy.JPG

fixture post pad 187 ms 2 pcs.DXF

fixture shelf 11 ga ms.DXF

[motoguy]

I am definitely cutting one of these! I see your .003 gap comment, for laser. Anyone have a suggestion for plasma cutting?

[Lowagon]

excellent share hemichargersrt8, thank you

[hemichargersrt8]

Motoguy raised a valid concern and since I don't have access to a plasma table, I created a test piece. Cut two of the puzzle test pieces prior to cutting to test your tables offsets. The puzzle tabs should fit into the slots.

puzzle tab test.JPG

puzzle tab test exp.JPG

fixture tab test 187 ms 2 pcs.DXF

[sr guy]

awesome job thanks for the share!!

[motoguy]

Motoguy raised a valid concern and since I don't have access to a plasma table, I created a test piece. Cut two of the puzzle test pieces prior to cutting to test your tables offsets. The puzzle tabs should fit into the slots.

My hat is off, sir. You are definitely going above and beyond on this. Thanks!

[richiemirtsching]

Yes thank you for the help

[scottlane]

Thanks for the file. Looks great.

[badassr1]

Yes sir thanks a ton I just started one of these a week ago.. Save me a lot of time.. Big thanks

[hemichargersrt8]

To help hold the table top and slats temporarily until you have the assembly tacked together, cut a handful of these brackets out of some scrap steel. As you assemble, bolt in a few locations to make your life easier.

weld assy assistance bracket.JPG

fixture assy bracket 187 ms.DXF

[sr guy]

https://www.amazon.com/Construction-Rea ... 2F8+reamer

Im thinking this will work to make sure the holes have no taper after cutting. Any ideas thoughts or comments?